http://WWW.CHEMICALEARTHINGELECTRODE.COM
http://WWW.CHEMICALEARTHINGELECTRODE.COM

Checking delivery availability...

background-sm
Search

Updates found with 'construction'

Page  1 1

Updates found with 'construction'

Electrical Notes & ArticlesWhat is Earthing Jignesh.Parmar5 years agoIntroduction:The main reason for doing earthing in electrical network is for the safety. When all metallic parts in electrical equipments are grounded then if the insulation inside the equipments fails there are no dangerous voltages present in the equipment case. If the live wire touches the grounded case then the circuit is effectively shorted and fuse will immediately blow. When the fuse is blown then the dangerous voltages are away.Purpose of Earthing:(1)  Safety for Human life/ Building/Equipments:To save human life from danger of electrical shock or death by blowing a fuse i.e. To provide an alternative path for the fault current to flow so that it will not endanger the userTo protect buildings, machinery & appliances under fault conditions.To ensure that all exposed conductive parts do not reach a dangerous potential.To provide safe path to dissipate lightning and short circuit currents.To provide stable platform for operation of sensitive  electronic equipments   i.e. To maintain the voltage at any part of an electrical system at a known value so as to prevent over current or excessive voltage on the appliances or equipment .(2)  Over voltage protection:Lightning, line surges or unintentional contact with higher voltage lines can cause dangerously high voltages to the electrical distribution system. Earthing provides an alternative path around the electrical system to minimize damages in the System.(3)  Voltage stabilization:There are many sources of electricity. Every transformer can be considered a separate source. If there were not a common reference point for all these voltage sources it would be extremely difficult to calculate their relationships to each other. The earth is the most omnipresent conductive surface, and so it was adopted in the very beginnings of electrical distribution systems as a nearly universal standard for all electric systems.Conventional methods of earthing:(1)  Plate type Earthing:Generally for plate type earthing normal Practice is to useCast iron plate of size 600 mm x600 mm x12 mm. ORGalvanized iron plate of size 600 mm x600 mm x6 mm. ORCopper plate of size 600 mm * 600 mm * 3.15 mmPlate  burred at the depth of 8 feet in the vertical position and GI strip of size 50 mmx6 mm bolted with the plate is brought up to the ground level.These types of earth pit are generally filled with alternate layer of charcoal & salt up to 4 feet from the bottom of the pit.(2)  Pipe type Earthing:For Pipe type earthing normal practice is to useGI pipe [C-class] of 75 mm diameter, 10 feet long welded with 75 mm diameter GI flange having 6 numbers of holes for the connection of earth wires and inserted in ground by auger method.These types of earth pit are generally filled with alternate layer of charcoal & salt or earth reactivation compound.Method for Construction of Earthing Pit (Indian Electricity Board):Excavation on earth for a normal earth Pit size is 1.5M X 1.5M X 3.0 M.Use 500 mm X 500 mm X 10 mm GI Plate or Bigger Size for more Contact of Earth and reduce Earth Resistance. Make a mixture of Wood Coal Powder Salt & Sand all in equal part Wood Coal Powder use as good conductor of electricity, anti corrosive, rust proves for GI Plate for long life.The purpose of coal and salt is to keep wet the soil permanently.The salt percolates and coal absorbs water keeping the soil wet.Care should always be taken by watering the earth pits in summer so that the pit soil will be wet.Coal is made of carbon which is good conductor minimizing the earth resistant.Salt use as electrolyte to form conductivity between GI Plate Coal and Earth with humidity.Sand has used to form porosity to cycle water & humidity around the mixture.Put GI Plate (EARTH PLATE) of size 500 mm X 500 mm X 10 mm in the mid of mixture.Use Double GI Strip size 30 mm X 10 mm to connect GI Plate to System Earthling. It will be better to use GI Pipe of size 2.5″ diameter with a Flange on the top of GI Pipe to cover GI Strip from EARTH PLATE to Top Flange.Cover Top of GI pipe with a T joint to avoid jamming of pipe with dust & mud and also use water time to time through this pipe to bottom of earth plate.Maintain less than one Ohm Resistance from EARTH PIT conductor to a distance of 15 Meters around the EARTH PIT with another conductor dip on the Earth at least 500 mm deep.Check Voltage between Earth Pit conductors to Neutral of Mains Supply 220V AC 50 Hz it should be less than 2.0 Volts.Factors affecting on Earth resistivity:(1)  Soil Resistivity:    It is the resistance of soil to the passage of electric current. The earth resistance value (ohmic value) of an earth pit depends on soil resistivity. It is the resistance of the soil to the passage of electric current.It varies from soil to soil. It depends on the physical composition of the soil, moisture, dissolved salts, grain size and distribution, seasonal variation, current magnitude etc.In depends on the composition of soil, Moisture content, Dissolved salts, grain size and its distribution, seasonal variation, current magnitude.(2)  Soil Condition:Different soil conditions give different soil resistivity. Most of the soils are very poor conductors of electricity when they are completely dry. Soil resistivity is measured in ohm-meters or ohm-cm.Soil plays a significant role in determining the performance of Electrode.Soil with low resistivity is highly corrosive. If soil is dry then soil resistivity value will be very high.If soil resistivity is high, earth resistance of electrode will also be high.(3)  Moisture:  Moisture has a great influence on resistivity value of soil. The resistivity of a soil can be determined by the quantity of water held by the soil and resistivity of the water itself. Conduction of electricity in soil is through water.The resistance drops quickly to a more or less steady minimum value of about 15% moisture. And further increase of moisture level in soil will have little effect on soil resistivity. In many locations water table goes down in dry weather conditions. Therefore, it is essential to pour water in and around the earth pit to maintain moisture in dry weather conditions. Moisture significantly influences soil resistivity(4)  Dissolved salts:Pure water is poor conductor of electricity.Resistivity of soil depends on resistivity of water which in turn depends on the amount and nature of salts dissolved in it.Small quantity of salts in water reduces soil resistivity by 80%. common salt is most effective in improving conductivity of soil. But it corrodes metal and hence discouraged.(5)  Climate Condition:Increase or decrease of moisture content determines the increase or decrease of soil resistivity.Thus in dry whether resistivity will be very high and in monsoon months the resistivity will be low. (6)  Physical Composition:Different soil composition gives different average resistivity. Based on the type of soil, the resistivity of clay soil may be in the range of 4 – 150 ohm-meter, whereas for rocky or gravel soils, the same may be well above 1000 ohm-meter. (7)  Location of Earth Pit :The location also contributes to resistivity to a great extent. In a sloping landscape, or in a land with made up of soil, or areas which are hilly, rocky or sandy, water runs off and in dry weather conditions water table goes down very fast. In such situation Back fill Compound will not be able to attract moisture, as the soil around the pit would be dry. The earth pits located in such areas must be watered at frequent intervals, particularly during dry weather conditions.Though back fill compound retains moisture under normal conditions, it gives off moisture during dry weather to the dry soil around the electrode, and in the process loses moisture over a period of time. Therefore, choose a site that is naturally not well drained. (8)  Effect of grain size and its distribution:Grain size, its distribution and closeness of packing are also contributory factors, since they control the manner in which the moisture is held in the soil.Effect of seasonal variation on soil resistivity: Increase or decrease of moisture content in soil determines decrease or increase of soil resistivity. Thus in dry weather resistivity will be very high and during rainy season the resistivity will be low.(9)  Effect of current magnitude:Soil resistivity in the vicinity of ground electrode may be affected by current flowing from the electrode into the surrounding soil.The thermal characteristics and the moisture content of the soil will determine if a current of a given magnitude and duration will cause significant drying and thus increase the effect of soil resistivity(10) Area Available:Single electrode rod or strip or plate will not achieve the desired resistance alone. If a number of electrodes could be installed and interconnected the desired resistance could be achieved. The distance between the electrodes must be equal to the driven depth to avoid overlapping of area of influence. Each electrode, therefore, must be outside the resistance area of the other.(11)  Obstructions:The soil may look good on the surface but there may be obstructions below a few feet like virgin rock. In that event resistivity will be affected. Obstructions like concrete structure near about the pits will affect resistivity. If the earth pits are close by, the resistance value will be high.(12)    Current Magnitude:A current of significant magnitude and duration will cause significant drying condition in soil and thus increase the soil resistivity.Measurement of Earth Resistance by use of Earth Tester:For measuring soil resistivity Earth Tester is used. It is also called the “MEGGER”.It has a voltage source, a meter to measure Resistance in ohms, switches to change instrument range, Wires to connect terminal to Earth Electrode and Spikes.It is measured by using Four Terminal Earth Tester Instrument. The terminals are connected by wires as in illustration.P=Potential Spike and C=Current Spike. The distance between the spikes may be 1M, 2M, 5M, 10M, 35M, and 50M.All spikes are equidistant and in straight line to maintain electrical continuity.  Take measurement in different directions.Soil resistivity =2πLR.R= Value of Earth resistance in ohm.Distance between the spikes in cm.π  =  3.14P = Earth resistivity ohm-cm.Earth resistance value is directly proportional to Soil resistivity valueMeasurement of Earth Resistance (Three point method): In this method earth tester terminal C1 & P1 are shorted to each other and connected to the earth electrode (pipe) under test.Terminals P2 & C2 are connected to the two separate spikes driven in earth.  These two spikes are kept in same line at the distance of 25 meters and 50 meters due to which there will not be mutual interference in the field of individual spikes.If we rotate generator handle with specific speed we get directly earth resistance on scale.Spike length in the earth should not be more than 1/20th distance between two spikes.Resistance must be verified by increasing or decreasing the distance between the tester electrode and the spikes by 5 meter. Normally, the length of wires should be 10 and 15 Meter or in proportion of 62% of ‘D’.Suppose, the distance of Current Spike from Earth Electrode D = 60 ft, Then, distance of Potential Spike would be 62 % of D = 0.62D i.e.  0.62 x 60 ft = 37 ft.Four Point Method:In this method 4 spikes are driven in earth in same line at the equal distance.  Outer two spikes are connected to C1 & C2 terminals of earth tester.  Similarly inner two spikes are connected to P1 & P2 terminals.  Now if we rotate generator handle with specific speed, we get earth resistance value of that place.In this method error due to polarization effect is eliminated and earth tester can be operated directly on A.C. GI Earthing Vs Copper Earthing:As per IS 3043, the resistance of Plate electrode to earth (R) = (r/A) X under root(P/A).Where r = Resistivity of Soil Ohm-meter.A=Area of Earthing Plate m3.The resistance of Pipe electrode to earth (R) = (100r/2πL) X loge (4L/d).Where L= Length of Pipe/Rod in cmd=Diameter of Pipe/Rod in cm.The resistivity of the soil and the physical dimensions of the electrode play important role of resistance of Rod with earth.The material resistivity is not considered important role in earth resistivity.Any material of given dimensions would offer the same resistance to earth. Except the sizing and number of the earthing conductor or the protective conductor. Pipe Earthing Vs Plate Earthing:Suppose Copper Plate having of size 1.2m x 1.2m x 3.15mm thick. soil resistivity of 100 ohm-m, The resistance of Plate electrode to earth (R)=( r/A)X under root(π/A) = (100/2.88)X(3.14/2.88)=36.27 ohmNow, consider a GI Pipe Electrode of 50 mm Diameter and 3 m Long. soil resistivity of 100 Ohm-m, The resistance of Pipe electrode to earth (R) = (100r/2πL) X loge (4L/d) = (100X100/2X3.14X300) X loge (4X300/5) =29.09 Ohm.From the above calculation the GI Pipe electrode offers a much lesser resistance than even a copper plate electrode.As per IS 3043 Pipe, rod or strip has a much lower resistance than a plate of equal surface area. Length of Pipe Electrode and Earthing Pit: The resistance to earth of a pipe or plate electrode reduces rapidly within the first few feet from ground (mostly 2 to 3 meter) but after that soil resistivity is mostly uniform.After about 4 meter depth, there is no appreciable change in resistance to earth of the electrode. Except a number of rods in parallel are to be preferred to a single long rod. Amount of Salt and Charcoal (more than 8Kg) : To reduce soil resistivity, it is necessary to dissolve in the moisture particle in the Soil.Some substance like Salt/Charcoal is highly conductive in water solution but the additive substance would reduce the resistivity of the soil, only when it is dissolved in the moisture in the soil after that additional quantity does not serve the Purpose.5% moisture in Salt reduces earth resistivity rapidly and further increase in salt content will give a very little decrease in soil resistivity.The salt content is expressed in percent by weight of the moisture content in the soil. Considering 1M3 of Soil, the moisture content at 10 percent will be about 144 kg. (10 percent of 1440 kg). The salt content shall be 5% of this (i.e.) 5% of 144kg, that is, about 7.2kg. Amount of  Water Purring: Moisture content is one of the controlling factors of earth resistivity.Above 20 % of moisture content, the resistivity is very little affected. But below 20% the resistivity increases rapidly with the decrease in moisture content.If the moisture content is already above 20% there is no point in adding quantity of water into the earth pit, except perhaps wasting an important and scarce national resource like water. Length Vs Diameter of Earth Electrode:Apart from considerations of mechanical strength, there is little advantage to be gained from increasing the earth electrode diameter with the object in mind of increasing surface area in contact with the soil.The usual practice is to select a diameter of earth electrode, which will have enough strength to enable it to be driven into the particular soil conditions without bending or splitting. Large diameter electrode may be more difficult to drive than smaller diameter electrode.The depth to which an earth electrode is driven has much more influence on its electrical resistance characteristics than has its diameter.Maximum allowable Earth resistance:Major power station= 0.5 Ohm.Major Sub-stations= 1.0 OhmMinor Sub-station = 2 OhmNeutral Bushing. =2 OhmService connection = 4 OhmMedium Voltage Network =2 OhmL.T.Lightening Arrestor= 4 OhmL.T.Pole= 5 OhmH.T.Pole =10 OhmTower =20-30 Ohm Treatments to for minimizing Earth resistance:Remove Oxidation on joints and joints should be tightened.Poured sufficient water in earth electrode.Used bigger size of Earth Electrode.Electrodes should be connected in parallel.Earth pit of more depth & width- breadth should be made.About these adsCategories: UncategorizedLeave a CommentElectrical Notes & ArticlesCreate a free website or blog at WordPress.com.Back to top
Send Enquiry
Read More
Electrical Notes & ArticlesWhat is Earthing Jignesh.Parmar5 years agoIntroduction:The main reason for doing earthing in electrical network is for the safety. When all metallic parts in electrical equipments are grounded then if the insulation inside the equipments fails there are no dangerous voltages present in the equipment case. If the live wire touches the grounded case then the circuit is effectively shorted and fuse will immediately blow. When the fuse is blown then the dangerous voltages are away.Purpose of Earthing:(1)  Safety for Human life/ Building/Equipments:To save human life from danger of electrical shock or death by blowing a fuse i.e. To provide an alternative path for the fault current to flow so that it will not endanger the userTo protect buildings, machinery & appliances under fault conditions.To ensure that all exposed conductive parts do not reach a dangerous potential.To provide safe path to dissipate lightning and short circuit currents.To provide stable platform for operation of sensitive  electronic equipments   i.e. To maintain the voltage at any part of an electrical system at a known value so as to prevent over current or excessive voltage on the appliances or equipment .(2)  Over voltage protection:Lightning, line surges or unintentional contact with higher voltage lines can cause dangerously high voltages to the electrical distribution system. Earthing provides an alternative path around the electrical system to minimize damages in the System.(3)  Voltage stabilization:There are many sources of electricity. Every transformer can be considered a separate source. If there were not a common reference point for all these voltage sources it would be extremely difficult to calculate their relationships to each other. The earth is the most omnipresent conductive surface, and so it was adopted in the very beginnings of electrical distribution systems as a nearly universal standard for all electric systems.Conventional methods of earthing:(1)  Plate type Earthing:Generally for plate type earthing normal Practice is to useCast iron plate of size 600 mm x600 mm x12 mm. ORGalvanized iron plate of size 600 mm x600 mm x6 mm. ORCopper plate of size 600 mm * 600 mm * 3.15 mmPlate  burred at the depth of 8 feet in the vertical position and GI strip of size 50 mmx6 mm bolted with the plate is brought up to the ground level.These types of earth pit are generally filled with alternate layer of charcoal & salt up to 4 feet from the bottom of the pit.(2)  Pipe type Earthing:For Pipe type earthing normal practice is to useGI pipe [C-class] of 75 mm diameter, 10 feet long welded with 75 mm diameter GI flange having 6 numbers of holes for the connection of earth wires and inserted in ground by auger method.These types of earth pit are generally filled with alternate layer of charcoal & salt or earth reactivation compound.Method for Construction of Earthing Pit (Indian Electricity Board):Excavation on earth for a normal earth Pit size is 1.5M X 1.5M X 3.0 M.Use 500 mm X 500 mm X 10 mm GI Plate or Bigger Size for more Contact of Earth and reduce Earth Resistance. Make a mixture of Wood Coal Powder Salt & Sand all in equal part Wood Coal Powder use as good conductor of electricity, anti corrosive, rust proves for GI Plate for long life.The purpose of coal and salt is to keep wet the soil permanently.The salt percolates and coal absorbs water keeping the soil wet.Care should always be taken by watering the earth pits in summer so that the pit soil will be wet.Coal is made of carbon which is good conductor minimizing the earth resistant.Salt use as electrolyte to form conductivity between GI Plate Coal and Earth with humidity.Sand has used to form porosity to cycle water & humidity around the mixture.Put GI Plate (EARTH PLATE) of size 500 mm X 500 mm X 10 mm in the mid of mixture.Use Double GI Strip size 30 mm X 10 mm to connect GI Plate to System Earthling. It will be better to use GI Pipe of size 2.5″ diameter with a Flange on the top of GI Pipe to cover GI Strip from EARTH PLATE to Top Flange.Cover Top of GI pipe with a T joint to avoid jamming of pipe with dust & mud and also use water time to time through this pipe to bottom of earth plate.Maintain less than one Ohm Resistance from EARTH PIT conductor to a distance of 15 Meters around the EARTH PIT with another conductor dip on the Earth at least 500 mm deep.Check Voltage between Earth Pit conductors to Neutral of Mains Supply 220V AC 50 Hz it should be less than 2.0 Volts.Factors affecting on Earth resistivity:(1)  Soil Resistivity:    It is the resistance of soil to the passage of electric current. The earth resistance value (ohmic value) of an earth pit depends on soil resistivity. It is the resistance of the soil to the passage of electric current.It varies from soil to soil. It depends on the physical composition of the soil, moisture, dissolved salts, grain size and distribution, seasonal variation, current magnitude etc.In depends on the composition of soil, Moisture content, Dissolved salts, grain size and its distribution, seasonal variation, current magnitude.(2)  Soil Condition:Different soil conditions give different soil resistivity. Most of the soils are very poor conductors of electricity when they are completely dry. Soil resistivity is measured in ohm-meters or ohm-cm.Soil plays a significant role in determining the performance of Electrode.Soil with low resistivity is highly corrosive. If soil is dry then soil resistivity value will be very high.If soil resistivity is high, earth resistance of electrode will also be high.(3)  Moisture:  Moisture has a great influence on resistivity value of soil. The resistivity of a soil can be determined by the quantity of water held by the soil and resistivity of the water itself. Conduction of electricity in soil is through water.The resistance drops quickly to a more or less steady minimum value of about 15% moisture. And further increase of moisture level in soil will have little effect on soil resistivity. In many locations water table goes down in dry weather conditions. Therefore, it is essential to pour water in and around the earth pit to maintain moisture in dry weather conditions. Moisture significantly influences soil resistivity(4)  Dissolved salts:Pure water is poor conductor of electricity.Resistivity of soil depends on resistivity of water which in turn depends on the amount and nature of salts dissolved in it.Small quantity of salts in water reduces soil resistivity by 80%. common salt is most effective in improving conductivity of soil. But it corrodes metal and hence discouraged.(5)  Climate Condition:Increase or decrease of moisture content determines the increase or decrease of soil resistivity.Thus in dry whether resistivity will be very high and in monsoon months the resistivity will be low. (6)  Physical Composition:Different soil composition gives different average resistivity. Based on the type of soil, the resistivity of clay soil may be in the range of 4 – 150 ohm-meter, whereas for rocky or gravel soils, the same may be well above 1000 ohm-meter. (7)  Location of Earth Pit :The location also contributes to resistivity to a great extent. In a sloping landscape, or in a land with made up of soil, or areas which are hilly, rocky or sandy, water runs off and in dry weather conditions water table goes down very fast. In such situation Back fill Compound will not be able to attract moisture, as the soil around the pit would be dry. The earth pits located in such areas must be watered at frequent intervals, particularly during dry weather conditions.Though back fill compound retains moisture under normal conditions, it gives off moisture during dry weather to the dry soil around the electrode, and in the process loses moisture over a period of time. Therefore, choose a site that is naturally not well drained. (8)  Effect of grain size and its distribution:Grain size, its distribution and closeness of packing are also contributory factors, since they control the manner in which the moisture is held in the soil.Effect of seasonal variation on soil resistivity: Increase or decrease of moisture content in soil determines decrease or increase of soil resistivity. Thus in dry weather resistivity will be very high and during rainy season the resistivity will be low.(9)  Effect of current magnitude:Soil resistivity in the vicinity of ground electrode may be affected by current flowing from the electrode into the surrounding soil.The thermal characteristics and the moisture content of the soil will determine if a current of a given magnitude and duration will cause significant drying and thus increase the effect of soil resistivity(10) Area Available:Single electrode rod or strip or plate will not achieve the desired resistance alone. If a number of electrodes could be installed and interconnected the desired resistance could be achieved. The distance between the electrodes must be equal to the driven depth to avoid overlapping of area of influence. Each electrode, therefore, must be outside the resistance area of the other.(11)  Obstructions:The soil may look good on the surface but there may be obstructions below a few feet like virgin rock. In that event resistivity will be affected. Obstructions like concrete structure near about the pits will affect resistivity. If the earth pits are close by, the resistance value will be high.(12)    Current Magnitude:A current of significant magnitude and duration will cause significant drying condition in soil and thus increase the soil resistivity.Measurement of Earth Resistance by use of Earth Tester:For measuring soil resistivity Earth Tester is used. It is also called the “MEGGER”.It has a voltage source, a meter to measure Resistance in ohms, switches to change instrument range, Wires to connect terminal to Earth Electrode and Spikes.It is measured by using Four Terminal Earth Tester Instrument. The terminals are connected by wires as in illustration.P=Potential Spike and C=Current Spike. The distance between the spikes may be 1M, 2M, 5M, 10M, 35M, and 50M.All spikes are equidistant and in straight line to maintain electrical continuity.  Take measurement in different directions.Soil resistivity =2πLR.R= Value of Earth resistance in ohm.Distance between the spikes in cm.π  =  3.14P = Earth resistivity ohm-cm.Earth resistance value is directly proportional to Soil resistivity valueMeasurement of Earth Resistance (Three point method): In this method earth tester terminal C1 & P1 are shorted to each other and connected to the earth electrode (pipe) under test.Terminals P2 & C2 are connected to the two separate spikes driven in earth.  These two spikes are kept in same line at the distance of 25 meters and 50 meters due to which there will not be mutual interference in the field of individual spikes.If we rotate generator handle with specific speed we get directly earth resistance on scale.Spike length in the earth should not be more than 1/20th distance between two spikes.Resistance must be verified by increasing or decreasing the distance between the tester electrode and the spikes by 5 meter. Normally, the length of wires should be 10 and 15 Meter or in proportion of 62% of ‘D’.Suppose, the distance of Current Spike from Earth Electrode D = 60 ft, Then, distance of Potential Spike would be 62 % of D = 0.62D i.e.  0.62 x 60 ft = 37 ft.Four Point Method:In this method 4 spikes are driven in earth in same line at the equal distance.  Outer two spikes are connected to C1 & C2 terminals of earth tester.  Similarly inner two spikes are connected to P1 & P2 terminals.  Now if we rotate generator handle with specific speed, we get earth resistance value of that place.In this method error due to polarization effect is eliminated and earth tester can be operated directly on A.C. GI Earthing Vs Copper Earthing:As per IS 3043, the resistance of Plate electrode to earth (R) = (r/A) X under root(P/A).Where r = Resistivity of Soil Ohm-meter.A=Area of Earthing Plate m3.The resistance of Pipe electrode to earth (R) = (100r/2πL) X loge (4L/d).Where L= Length of Pipe/Rod in cmd=Diameter of Pipe/Rod in cm.The resistivity of the soil and the physical dimensions of the electrode play important role of resistance of Rod with earth.The material resistivity is not considered important role in earth resistivity.Any material of given dimensions would offer the same resistance to earth. Except the sizing and number of the earthing conductor or the protective conductor. Pipe Earthing Vs Plate Earthing:Suppose Copper Plate having of size 1.2m x 1.2m x 3.15mm thick. soil resistivity of 100 ohm-m, The resistance of Plate electrode to earth (R)=( r/A)X under root(π/A) = (100/2.88)X(3.14/2.88)=36.27 ohmNow, consider a GI Pipe Electrode of 50 mm Diameter and 3 m Long. soil resistivity of 100 Ohm-m, The resistance of Pipe electrode to earth (R) = (100r/2πL) X loge (4L/d) = (100X100/2X3.14X300) X loge (4X300/5) =29.09 Ohm.From the above calculation the GI Pipe electrode offers a much lesser resistance than even a copper plate electrode.As per IS 3043 Pipe, rod or strip has a much lower resistance than a plate of equal surface area. Length of Pipe Electrode and Earthing Pit: The resistance to earth of a pipe or plate electrode reduces rapidly within the first few feet from ground (mostly 2 to 3 meter) but after that soil resistivity is mostly uniform.After about 4 meter depth, there is no appreciable change in resistance to earth of the electrode. Except a number of rods in parallel are to be preferred to a single long rod. Amount of Salt and Charcoal (more than 8Kg) : To reduce soil resistivity, it is necessary to dissolve in the moisture particle in the Soil.Some substance like Salt/Charcoal is highly conductive in water solution but the additive substance would reduce the resistivity of the soil, only when it is dissolved in the moisture in the soil after that additional quantity does not serve the Purpose.5% moisture in Salt reduces earth resistivity rapidly and further increase in salt content will give a very little decrease in soil resistivity.The salt content is expressed in percent by weight of the moisture content in the soil. Considering 1M3 of Soil, the moisture content at 10 percent will be about 144 kg. (10 percent of 1440 kg). The salt content shall be 5% of this (i.e.) 5% of 144kg, that is, about 7.2kg. Amount of  Water Purring: Moisture content is one of the controlling factors of earth resistivity.Above 20 % of moisture content, the resistivity is very little affected. But below 20% the resistivity increases rapidly with the decrease in moisture content.If the moisture content is already above 20% there is no point in adding quantity of water into the earth pit, except perhaps wasting an important and scarce national resource like water. Length Vs Diameter of Earth Electrode:Apart from considerations of mechanical strength, there is little advantage to be gained from increasing the earth electrode diameter with the object in mind of increasing surface area in contact with the soil.The usual practice is to select a diameter of earth electrode, which will have enough strength to enable it to be driven into the particular soil conditions without bending or splitting. Large diameter electrode may be more difficult to drive than smaller diameter electrode.The depth to which an earth electrode is driven has much more influence on its electrical resistance characteristics than has its diameter.Maximum allowable Earth resistance:Major power station= 0.5 Ohm.Major Sub-stations= 1.0 OhmMinor Sub-station = 2 OhmNeutral Bushing. =2 OhmService connection = 4 OhmMedium Voltage Network =2 OhmL.T.Lightening Arrestor= 4 OhmL.T.Pole= 5 OhmH.T.Pole =10 OhmTower =20-30 Ohm Treatments to for minimizing Earth resistance:Remove Oxidation on joints and joints should be tightened.Poured sufficient water in earth electrode.Used bigger size of Earth Electrode.Electrodes should be connected in parallel.Earth pit of more depth & width- breadth should be made.About these adsCategories: UncategorizedLeave a CommentElectrical Notes & ArticlesCreate a free website or blog at WordPress.com.Back to top
Send Enquiry
Read More
The main reason for doing earthing in electrical network is for the safety. When all metallic parts in electrical equipments are grounded then if the insulation inside the equipments fails there are no dangerous voltages present in the equipment case. If the live wire touches the grounded case then the circuit is effectively shorted and fuse will immediately blow. When the fuse is blown then the dangerous voltages are away.Purpose of Earthing:(1)  Safety for Human life/ Building/Equipments:To save human life from danger of electrical shock or death by blowing a fuse i.e. To provide an alternative path for the fault current to flow so that it will not endanger the userTo protect buildings, machinery & appliances under fault conditions.To ensure that all exposed conductive parts do not reach a dangerous potential.To provide safe path to dissipate lightning and short circuit currents.To provide stable platform for operation of sensitive  electronic equipments   i.e. To maintain the voltage at any part of an electrical system at a known value so as to prevent over current or excessive voltage on the appliances or equipment .(2)  Over voltage protection:Lightning, line surges or unintentional contact with higher voltage lines can cause dangerously high voltages to the electrical distribution system. Earthing provides an alternative path around the electrical system to minimize damages in the System.(3)  Voltage stabilization:There are many sources of electricity. Every transformer can be considered a separate source. If there were not a common reference point for all these voltage sources it would be extremely difficult to calculate their relationships to each other. The earth is the most omnipresent conductive surface, and so it was adopted in the very beginnings of electrical distribution systems as a nearly universal standard for all electric systems.Conventional methods of earthing:(1)  Plate type Earthing:Generally for plate type earthing normal Practice is to useCast iron plate of size 600 mm x600 mm x12 mm. ORGalvanized iron plate of size 600 mm x600 mm x6 mm. ORCopper plate of size 600 mm * 600 mm * 3.15 mmPlate  burred at the depth of 8 feet in the vertical position and GI strip of size 50 mmx6 mm bolted with the plate is brought up to the ground level.These types of earth pit are generally filled with alternate layer of charcoal & salt up to 4 feet from the bottom of the pit.(2)  Pipe type Earthing:For Pipe type earthing normal practice is to useGI pipe [C-class] of 75 mm diameter, 10 feet long welded with 75 mm diameter GI flange having 6 numbers of holes for the connection of earth wires and inserted in ground by auger method.These types of earth pit are generally filled with alternate layer of charcoal & salt or earth reactivation compound.Method for Construction of Earthing Pit (Indian Electricity Board):Excavation on earth for a normal earth Pit size is 1.5M X 1.5M X 3.0 M.Use 500 mm X 500 mm X 10 mm GI Plate or Bigger Size for more Contact of Earth and reduce Earth Resistance. Make a mixture of Wood Coal Powder Salt & Sand all in equal part Wood Coal Powder use as good conductor of electricity, anti corrosive, rust proves for GI Plate for long life.The purpose of coal and salt is to keep wet the soil permanently.The salt percolates and coal absorbs water keeping the soil wet.Care should always be taken by watering the earth pits in summer so that the pit soil will be wet.Coal is made of carbon which is good conductor minimizing the earth resistant.Salt use as electrolyte to form conductivity between GI Plate Coal and Earth with humidity.Sand has used to form porosity to cycle water & humidity around the mixture.Put GI Plate (EARTH PLATE) of size 500 mm X 500 mm X 10 mm in the mid of mixture.Use Double GI Strip size 30 mm X 10 mm to connect GI Plate to System Earthling. It will be better to use GI Pipe of size 2.5″ diameter with a Flange on the top of GI Pipe to cover GI Strip from EARTH PLATE to Top Flange.Cover Top of GI pipe with a T joint to avoid jamming of pipe with dust & mud and also use water time to time through this pipe to bottom of earth plate.Maintain less than one Ohm Resistance from EARTH PIT conductor to a distance of 15 Meters around the EARTH PIT with another conductor dip on the Earth at least 500 mm deep.Check Voltage between Earth Pit conductors to Neutral of Mains Supply 220V AC 50 Hz it should be less than 2.0 Volts.
Send Enquiry
Read More
S – Earthing/Grounding RegulationsEarthing/Grounding RequirementsConductors and Earth rodsAs with lightning protection,  the first choice faced by the designer of an earthing system is the type of conductor to be used. The correctchoice of conductor is extremely important,  whether it be a simple below ground electrode or a complex computer room signal reference grid.ConductorsTypical conductor types include flat tape,  solid circular and stranded cable. For above ground applications,  copper,  aluminum and steel may be used. Below ground,  copper is the most common choice due to its high resistance to corrosion.Examples of typical earthing installationTypes of Earthing ConnectionsMechanical or Exothermic type connections are both used in the International World for earthing connections.  Specific countries and clients have preferences for one method or the other,  but in general,  both are widely used and are accepted engineering practice.Examples of typical earthing installationProtective equipotential bonding via multiple cablesTypical Earthing ArrangementVarious earthing and bonding conductors and componentsSurge Protective DevicesWhen using surge devices make sure they comply with IEC 61643 and connect in the appropriate mannerTypical Earthing Cable SizingThe cross‐sectional area of branch conductors connecting equipment and structures to plant earth ring shall be as followed as a rule of thumb as recommended by various earthing equipment manufacturers and IEC 62035 &  AS1768/2007To metallic enclosures of HV electrical equipment 70mm²To metallic enclosures of LV electrical equipment,  having a supply cable cross‐sectional area ≥ 35mm²70mm²To metallic enclosures of LV electrical equipment,  having a supply cable cross‐sectional area < 35mm²25mm²To control panels,  etc. 25mm²To non‐electrical equipment exposed to lighting,  e.g. tanks,  columns and tall structures70mm²To other non‐electrical equipment 25mm²Earthing and Bonding SystemsThe principal reasons for earthing and bonding in electrical installations are:• To eliminate the possibility of electric shock to personnel• To enable protection devices to operate correctly so that the duration of fault currents are kept to a minimum• To equalize the voltage potential of normally non‐current carrying metalwork• To prevent electrostatic charge of process plant to fluid movementIn hazardous areas,  the elimination of sources of ignition is very important and effective earthingand bonding play an important role.  EN60079‐14 clause 4.7 states that “care shall be taken to ensure that the earthing and potential equalization bonding provisions in hazardous areas are maintained in good condition”Types of common systems are as followed:• TN‐S – System has separate neutral and protective conductors throughout• TT – A system in which one point of the source of energy is directly earthed but which electrically independent of the electrodes used to earth the exposed conductive parts of the electrical system.• TN‐C – A system in which a single conductor serves as both the neutral and protective conductor in part of a system• IT – A system in which there is no direct connection between live parts and earth but exposed conductive parts of the electrical installation are earthed.The EN/IEC 60079‐14 installation directive requires equipotential bonding within hazardous areas of Zones 0 and 1 to prevent the occurrence of sparks capable of causing ignition or of a temperature rise caused by potential differences. Implementation of the equipotential bonding must comply with the system configuration to DIN VDE 0100 Part 410 and the design ratings to DIN VDE 0100 Part 540. Full equipotential bonding is achieved by connecting not only the housings of the electrical equipment into the equipotentialbonding,  but also all other accessible,  conductive structural parts such as building construction,  metal containers,  piping etc. Extraneous conductive parts which do not belong to the structure or installation of the system (e.g. door frames,  window frames) need not be incorporated into the equipotential bondingEquipotential Bonding in Hazardous AreasThe IEC started working on coming up with a universal design for plugs and sockets worldwide,  trying to ensure that dangerous situations could not arise during the periods when the new system and the multitude of existing ones had to exist side by side.  The first drafts of a universal system considered by SC 23C proposed all flat pins and this was pursued for many years. However,  at the voting stage,  objections grew and,  many National Committees expressed themselves more in favor of a round pin solution. The other serious problem encountered was in trying to find a unique solution for 125V and 250V distribution systems. After long,  and often acrimonious,  discussion,  the subcommittee came to an acceptable solution which was finally formulated in 1986 as publication IEC 906‐1 (now IEC 60906‐1) for 250V installations using round pins and in 1992 as IEC 906‐2 (now IEC 60906‐2) for 125V installations using the familiar US flat pin design.More recently,  in the 1990s,  CENELEC,  in Europe,  was put under pressure by the European Commission to devise a harmonized plug and socket system for Europe. CENELEC took as its starting point the IEC standard of 1986 and spent thousands of man‐hours undertaking the almost impossible task of modifying the design with the aim of ensuring 100% risk‐free operation of the system when used in conjunction with all the existing types in Europe. Naturally,  apart from the technical difficulties,  there was the clash of the many vested commercial and political interests and it was not surprising that,  after much work and many meetings,  CENELEC had to admit defeat and abandon its efforts.Universal Plug and Socket Systems??
Send Enquiry
Read More
Joints of protective conductors shall be accessible for inspection and testing except m compound-filled or encapsulated joints. No switching device shall is inserted in the protective conductor, but joints which can bedisconnected for test purposes by use of a tool may be provided. An auxiliary earth electrode shall be provided electrically' independent of all other earthed metal, forexample, constructional metalwork, pipes, or metal-sheathed cables. This requirement i. consideredto be fulfilled if the auxiliary earth electrode is installed at a specified distance from all other earthedmetal (value of distance under consideration). The earthing conductor leading to the auxiliary earth electrode shall be isolated to avoid contact withthe protective conductor or any of the parts connected thereto or extraneous conductive parts whichare, or may be, in contact with them. In TN systems, for cables in fixed installations having a cross sectional area not less than 10mm2forcopper and 16mm2for aluminum, a single conductor may serve both as protective conductor andneutral conductor, provided that the part of the installation concerned is not protected by a residualcurrent-operated device. However, the minimum cross sectional area of a PEN conductor may be 4mm2, provided that thecable is of a concentric type conforming to Indian Standards and that duplicate continuityconnections exist at all joints and terminations in the run of the concentric conductors. When the source of energy is privately owned, there should be no metallic connection with theGeneral public supply unless there has been consultation with the electricity authority concerned. It should be emphasized that an installation together with its source of energy may not consist entirely of one particular type of system. In such cases, each part of that installation may be requiredto be treated separately without detriment to other parts of the same installation. RCD's having Minimum Operating Currents Greater Than 30 mA -- These devices are intended to giveindirect shock risk protection. The neutral points of each separate electricity system which has to be earthed at the power station orsubstation. GI/Copper Plate Size: 500mmX500mmX10mm. Wood coal powder and salt are in same quantity. Size of GI Strip: 300mmX10mm Size of GI Pipe: 2.5" Diameter. Minimum 1Ω Resistance should be available at a distance of 15mt.  IR value of Earth resistance is less than 10Ω.  Earthing resistance of earthing rod is changed from 0.3Ω to 0...8Ω between summer to winter.  Distance between two earthing pit is 2 X Length of earthing electrode. If ground resistance is less than plate earthing (if hard rock) than Pipe earthing shall be used. Resistance between two earthing pit is negligible. Earthing of lighting protection should not mix with power system earthing. Lighting protection earthing should be 10 time stronger than normal earthing (use copper bus stripinstead of wire) Jointing of earthing strip shall be overlap of min 50mm and for earthing wire overlapping shall bemin 40mm
Send Enquiry
Read More
Page 1 0.9